Common Planner
Sign InCreate My Free Account!
Sign InCreate My Free Account!
K–12 Standards

Automotive Service II (2016): Grades 9, 10, 11, 12

Other North Carolina CTE sets

Adopted

Understand Engine Service1.00

  • I-A-4.

    Install engine covers using gaskets, seals, and sealers as required.I-A-4

  • I-A-6.

    Perform common fastener and thread repair, to include: remove broken bolt, restore internal and external threads, and repair internal threads with thread insert.I-A-6

  • I-C-3.

    Remove, inspect, and replace thermostat and gasket/seal.I-C-3

Understand Automatic Transmission/Transaxle Service2.00

  • II-B-1.

    Inspect, adjust, and replace external manual valve shift linkage, transmission range sensor/switch, and park/neutral position switch.II-B-1

Understand Manual Drive Train & Axle Service3.00

  • ASE-C-3.

    Inspect, adjust, and replace transmission/transaxle external shifter assembly, shift linkages, brackets, bushings/grommets, pivots, and levers.ASE-C-3

  • ASE-C-4.

    Inspect and replace external seals.ASE-C-4

  • ASE-C-8.

    Inspect, service, and replace drive shaft center support bearingsASE-C-8

  • ASE-C-14.

    Inspect, adjust, and repair transfer case manual shifting mechanisms, bushings, mounts, levers, and brackets.ASE-C-14

Understand Suspension & Steering Service4.00

  • IV-B-6.

    Inspect and replace power steering hoses and fittings.IV-B-6

  • IV-B-20.

    Inspect, remove, and replace shock absorbers; inspect mounts and bushings.IV-B-20

  • IV-B-23.

    Describe the function of the power steering pressure switch.IV-B-23

  • IV-D-3.

    Dismount, inspect, and remount tire on wheel; balance wheel and tire assembly (static and dynamic).IV-D-3

  • IV-D-4.

    Dismount, inspect, and remount tire on wheel equipped with tire pressure monitoring system sensor.IV-D-4

  • IV-D-6.

    Repair tire using internal patch.IV-D-6

  • IV-D-7.

    Identify and test tire pressure monitoring systems (indirect and direct) for operation; verify operation of instrument panel lamps.IV-D-7

  • IV-D-8.

    Demonstrate knowledge of steps required to remove and replace sensors in a tire pressure monitoring system.IV-D-8

  • ASE-D-5.

    Remove and replace power steering pump; inspect pump mounting and attaching brackets; remove and replace power steering pump pulley; transfer related components.ASE-D-5

Understand Brake Service5.00

  • V-A-2.

    Describe procedure for performing a road test to check brake system operation, including an anti-lock brake system (ABS).V-A-2

  • V-B-2.

    Check master cylinder for external leaks and proper operation.V-B-2

  • V-B-6.

    Bleed and/or flush brake system.V-B-6

  • V-C-1.

    Remove, clean, inspect, and measure brake drum diameter; determine necessary action.V-C-1

  • V-C-2.

    Refinish brake drum and measure final drum diameter; compare with specifications.V-C-2

  • V-C-3.

    Remove, clean, and inspect brake shoes, springs, pins, clips, levers, adjusters/self-adjusters, other related brake hardware, and backing support plates; lubricate and reassemble.V-C-3

  • V-C-4.

    Inspect wheel cylinders for leaks and proper operation; remove and replace as needed.V-C-4

  • V-C-5.

    Pre-adjust brake shoes and parking brake; install brake drums or drum/hub assemblies and wheel bearings; make final checks and adjustments.V-C-5

  • V-D-1.

    Remove and clean caliper assembly; inspect for leaks and damage/wear to caliper housing; determine necessary action.V-D-1

  • V-D-2.

    Clean and inspect caliper mounting and slides/pins for proper operation, wear, and damage; determine necessary action.V-D-2

  • V-D-3.

    Remove, inspect, and replace pads and retaining hardware; determine necessary action.V-D-3

  • V-D-4.

    Lubricate and reinstall caliper, pads, and related hardware; seat pads and inspect for leaks.V-D-4

  • V-D-5.

    Clean and inspect rotor, measure rotor thickness, thickness variation, and lateral runout; determine necessary action.V-D-5

  • V-D-6.

    Remove and reinstall rotor.V-D-6

  • V-D-7.

    Refinish rotor on vehicle; measure final rotor thickness and compare with specifications.V-D-7

  • V-D-8.

    Refinish rotor off vehicle; measure final rotor thickness and compare with specifications.V-D-8

  • V-D-9.

    Retract and re-adjust caliper piston on an integral parking brake system.V-D-9

  • V-D-11.

    Describe importance of operating vehicle to burnish/break-in replacement brake pads according to manufacturer's recommendations.V-D-11

  • V-F-1.

    Remove, clean, inspect, repack, and install wheel bearings; replace seals; install hub and adjust bearings.V-F-1

  • ASE-E-1.

    Check for poor stopping, pulling, dragging, noises, high or low pedal, and hard or spongy pedal.ASE-E-1

  • ASE-E-32.

    Inspect the vacuum-type power booster unit for operation, and vacuum leaks; inspect the check valve for proper operation.ASE-E-32

  • ASE-E-33.

    Identify operation of electric-hydraulic assist system; check system for leaks and operation.ASE-E-33

  • ASE-E-34.

    Identify operation of hydro-boost assist system; check system for leaks and operation.ASE-E-34

Understand Electrical/Electronic System Service6.00

  • VI-A-10.

    Perform solder repair of electrical wiring.VI-A-10

  • VI-A-11.

    Replace electrical connectors and terminal ends.VI-A-11

  • VI-C-1.

    Perform starter current draw test; determine necessary action.VI-C-1

  • VI-C-3.

    Inspect and test starter relays and solenoids; determine necessary action.VI-C-3

  • VI-C-4.

    Remove and install starter in a vehicle.VI-C-4

  • VI-C-5.

    Inspect and test switches, connectors, and wires of starter control circuits; determine necessary action.VI-C-5

  • VI-F-2.

    Remove and reinstall door panel.VI-F-2

  • ASE-F-21.

    Verify horn operation; determine needed repairsASE-F-21

Understand Heating & Air Conditioning Service7.00

  • VII-C-1.

    Inspect engine cooling and heater systems hoses; perform necessary action.VII-C-1

Understand Engine Performance Service8.00

  • VIII-A-7.

    Remove and replace spark plugs; inspect secondary ignition components for wear and damage.VIII-A-7

  • VIII-C-4.

    Inspect condition of exhaust system hangers, brackets, clamps, and heat shields; repair or replace as needed.VIII-C-4

Preparing Vehicle For Customer9.00

  • ST-D-1.

    Ensure vehicle is prepared to return to customer per school/company policy. (floor mats, steering wheel cover, etc.)ST-D-1

Personal Standards10.00

  • ST-E-1.

    Reports to work daily on time; able to take directions and motivated to accomplish the task at hand.ST-E-1

  • ST-E-2.

    Dresses appropriately and uses language and manners suitable for the workplace.ST-E-2

  • ST-E-3.

    Maintains appropriate personal hygiene.ST-E-3

  • ST-E-4.

    Meets and maintains employment eligibility criteria, such as drug/alcohol-free status, clean driving record, etc.ST-E-4

  • ST-E-5.

    Demonstrates honesty, integrity, and reliability.ST-E-5

Work Habits/Ethic11.00

  • ST-F-1.

    Complies with workplace policies/laws.ST-F-1

  • ST-F-2.

    Contributes to the success of the team, assists others and requests help when needed.ST-F-2

  • ST-F-3.

    Works well with all customers and coworkers.ST-F-3

  • ST-F-4.

    Negotiates solutions to interpersonal and workplace conflicts.ST-F-4

  • ST-F-5.

    Contributes ideas and initiative.ST-F-5

  • ST-F-6.

    Follows directionsST-F-6

  • ST-F-7.

    Communicates (written and verbal) effectively with customers and coworkers.ST-F-7

  • ST-F-8.

    Reads and interprets workplace documents; writes clearly and concisely.ST-F-8

  • ST-F-9.

    Analyzes and resolves problems that arise in completing assigned tasks.ST-F-9

  • ST-F-10.

    Organizes and implements a productive plan of work.ST-F-10

  • ST-F-11.

    Uses scientific, technical, engineering and mathematics principles and reasoning to accomplish assigned tasks.ST-F-11

  • ST-F-12.

    Identifies and address the needs of all customers, providing helpful, courteous and knowledgeable service and advice as needed.ST-F-12

Frequently asked questions

What grade levels do these standards cover?
Grade 9, Grade 10, Grade 11, and Grade 12
When were these standards adopted?
2016
Where can I read the official document?
Automotive Service II

Find this useful?

If so, you'll love the standards search built into Common Planner.

Keep exploring

Keep exploring CTE standards

Sibling grade bands, other subjects in this jurisdiction, and the same subject across other states.

More North Carolina CTE sets

CTE